You can't make old pipes new, but you can slow the wear that leads to slab leaks. The biggest steps are simple. Keep your water pressure in a safe range and deal with hard water. Set your water heater to about 120 degrees. Check your water meter now and then. Here is how.
Why Pipes Under Your Slab Wear Out
Many homes in both regions sit on concrete slabs. In Orange County, that includes many tract homes from the post-war years through the 1970s. In the Central Valley, slab-built tracts went up from the 1970s onward. The water lines run under that slab, most often in copper. You can't reach them without real work, so a leak there is a bigger job.
Copper under a slab does not fail at random. A few things wear it down over the years. Most of them you can check or change from above the floor.
- High water pressure. Every pipe and fixture works harder when pressure runs high.
- Hard water. Minerals in hard water leave scale in pipes, valves and heaters.
- Heat. Hot lines grow and shrink a little each time they heat and cool.
- Constant flow. A pump that moves hot water all day can wear copper from the inside.
- Rubbing. Pipes that shift can rub on concrete or gravel and wear thin.
- Soil movement. Expansive clay soils, common in the valley, swell and shrink with moisture.
- Age. Even good pipe has a lifespan, and many older homes are near the end of it.
This post covers what you can do about each one. Think you already have a leak? Jump to the short list of warning signs near the end, then call a plumber.
Check Your Water Pressure First
Start with pressure. It is one of the first things a plumber should check after any leak. It is easy to test, and a lot of pipe damage traces back to it. Pressure is measured in psi, which stands for pounds per square inch.
Most home plumbing guidance puts the safe range at about 40 to 80 psi. Many plumbers like to see it somewhere in the middle of that range. Higher is not better. It just means more stress on every joint.
How to Test It Yourself
- Buy a water pressure gauge that screws onto a hose bib. Hardware stores sell them.
- Pick the hose bib closest to where the water line enters your home.
- Turn off every faucet, sprinkler, dishwasher and washing machine.
- Screw the gauge on by hand and open the hose bib all the way.
- Read the needle. That number is your static pressure.
- Test again late at night, when city pressure often runs higher.
Some gauges have a second red needle that stays at the highest reading. Leave that kind on overnight. If the red needle sits well above your daytime number, your pressure is spiking. That often happens when the water heater warms a full tank and the water has no room to expand.
The usual fix for that is an expansion tank. It is a small tank that soaks up the extra pressure.
What a Pressure Regulator Does
A regulator is a bell-shaped valve. It sits on the main line, often near the front hose bib. Its job is to take high street pressure and bring it down to a safe level for your home. Plumbing codes generally call for one when street pressure is above 80 psi.
Hillside homes, like many in Yorba Linda and Corona, often get high pressure from the street. Flat valley neighborhoods can run high too, so test either way. Regulators also wear out. The spring and seals inside tire with age, and many start to slip after 10 years or so. A failed regulator can let full street pressure into the house. Watch for these signs:
- High reading. Your gauge shows more than 80 psi.
- Banging pipes. You hear a thump when a faucet or washer shuts off.
- Hissing toilets. They hiss or refill on their own.
- Spitting faucets. Water sprays when you first open the tap.
- Dripping relief valve. The valve on the side of your water heater leaks.
- Swinging pressure. Flow goes from strong to weak during the day.
Replacing a regulator is a common repair. It costs far less than chasing the leaks high pressure causes. See general plumbing repair.
Hard Water and What It Does to Your Pipes
Water is hard in both regions. Much of Orange County gets a blend of Colorado River water and State Water Project water. Many Central Valley cities rely on wells, and that groundwater is often hard too. Both carry a lot of calcium and magnesium. You see it as white crust on shower heads. Inside your plumbing, the same minerals build up as scale.
Scale narrows pipes and clogs faucet screens. It coats the bottom of tank water heaters and the inside of tankless units. That makes the heater work harder and wear out sooner. It can also keep valves from closing tight.
Water Softeners: Pros and Cons
A softener is a tank system that swaps hard minerals for sodium or potassium. It is not the right choice for every home. Here is a plain look at both sides.
What a Softener Does Well
- Less scale. Pipes, fixtures and water heaters stay cleaner.
- Better lather. Soap and shampoo work with less product.
- Fewer spots. Dishes and shower doors stay clearer.
- Easier on tankless heaters. They need descaling less often.
The Downsides
- Upkeep. You have to add salt and service the system.
- Sodium. It adds some sodium to your water.
- Space. The tank takes up room in the garage.
- Install work. Your home needs a plumbing loop to hook it up.
- Local rules. Some California cities and water districts limit salt-based softeners.
Many people keep one line unsoftened for drinking, or add a filter at the kitchen sink. Salt-free systems are also sold. They do not take minerals out of the water, and results vary. Ask plenty of questions before you buy, and check your local rules.
Even without a softener, you can fight scale. Flush your tank water heater once a year. Descale a tankless unit on the schedule in its manual. Soak shower heads in vinegar when flow drops.
Watch Your Water Meter and Your Bill
Your meter is a free leak detector. A slab leak can run for weeks before you see a drop of water. The meter sees it right away.
The Meter Test
- Find your meter box. It is usually near the curb or sidewalk.
- Lift the lid with a screwdriver. Watch for spiders.
- Turn off every faucet, sprinkler, ice maker and appliance in the home.
- Find the leak indicator. It is a small triangle or wheel on the dial.
- If it turns with everything off, water is going somewhere.
- For slow leaks, write down the reading. Use no water for two hours, then check again.
A moving meter does not always mean a slab leak. A running toilet or a leaky sprinkler valve will move it too, so check those first. Then close the main shutoff at the house. If the meter stops, the leak is past that valve, inside your home.
If it keeps moving, the leak is between the meter and the house. That often means a problem with the water service line in the yard. It is a different repair.
Read Your Bill
Compare each bill to the same months last year, not just the last bill. Summer watering makes bills climb every year. A jump you can't explain, with no change in habits, is worth a meter test. Many water providers show your use history.
Hot Water Lines, Recirculation Pumps and Heater Settings
Hot water is hard on copper. Hot lines grow and shrink a little each time they heat up and cool down. Where a pipe touches concrete or another pipe, that movement can wear a thin spot. That is one reason hot lines tend to leak first in many slab homes. A warm spot on the floor is often the first clue.
Recirculation Pumps
A recirculation pump keeps hot water moving through your pipes. That way it reaches the tap sooner, and you waste less water waiting. But a pump that runs all day pushes hot water through copper nonstop. Over time, that steady flow can wear the inside of the pipe, mostly at bends and fittings.
You don't have to give up hot water on demand. Most pumps can be set up to run less. A timer can run the pump only in the morning and evening. A push button or motion sensor runs it only when someone needs hot water. Either way, your lines get a rest.
Water Heater Temperature
A setting of about 120°F is widely suggested for most homes. It is hot enough for showers and dishes. Higher settings speed up scale, add stress to hot lines and raise the risk of burns. If your dial has no numbers, hold a kitchen thermometer under the hot tap to see where it sits.
A few more water heater habits help your pipes too:
- Straps. California requires seismic straps on water heaters, so check that yours are tight.
- Sediment. Flush a tank heater about once a year.
- Rust and water. Look around the base each season.
- Age and noise. Have it checked if it is over 10 years old or pops and rumbles.
Popping or rumbling usually means sediment on the bottom of the tank. In the valley, garage and attic heaters also sit through long, very hot summers. That heat is hard on the tank, its fittings and the relief valve. For an aging heater, see our water heater repair and replacement service.
Know Where Your Main Shutoff Is
Find it now, while nothing is wrong. When a pipe lets go, the minutes before the water is off decide how much damage you get. In most homes in the valley and Orange County, the main shutoff is in one of three places.
- Front or side of the house. Look near a hose bib.
- Garage. Some homes have it on a garage wall.
- Meter box by the curb. You may need a meter key to turn it.
Older homes often have a gate valve with a round handle. Newer homes often use a ball valve with a lever that takes a quarter turn. Once a year, turn your valve off and back on, gently. A gate valve that has not moved in 20 years can stick or break, so stop if it fights you.
Put a tag on the valve so anyone in the home can find it. Keep a meter key in the garage too.
Go Easy on Chemical Drain Cleaners
Skip the bottle. Most store drain cleaners use strong lye or acid to eat through a clog. They often don't clear it all the way. What's left sits in the trap and the pipe, still working on whatever it touches.
In older homes with cast iron or galvanized steel drains, that can speed up rust. Many older valley neighborhoods still have cast-iron or clay sewer lines. Some cleaners also get hot as they work, which can stress plastic pipe and glued joints. And if the drain stays clogged, a plumber now has to open a pipe full of harsh chemicals.
Better Ways to Keep Drains Clear
- Strainers. Put one in showers, tubs and the kitchen sink.
- Grease. Scrape it into the trash, not the drain.
- Hair. Pull it from tub and sink stoppers every few weeks.
- Simple clogs. Try a cheap plastic drain snake first.
- Repeat clogs. Call a plumber if the same drain keeps backing up.
A clog that keeps coming back usually has a cause further down the line. Chemicals won't fix that. Professional drain cleaning is safer.
When Old Pipes Are Due for a Repipe
Upkeep buys time. It does not reverse age. At some point, patching leak after leak costs more than new pipe. A whole-house repipe replaces the water lines in your home with PEX (flexible plastic water pipe) or copper. In slab homes, the new lines often run through the attic and walls.
Signs It's Time to Think About a Repipe
- Repeat leaks. You've had two or more in a year or two.
- A second slab leak. One was fixed, and now there's another.
- Rusty water. It runs brown, mostly after you've been away.
- Weak flow. Pressure has dropped at several fixtures, not just one.
- Galvanized pipe. Your home still has old steel water lines.
- Polybutylene pipe. This gray plastic pipe was used in many homes from the late 1970s to mid-1990s.
- A big remodel. The walls will be open anyway.
Pipe type matters. Galvanized steel rusts from the inside. It is common in older areas like Old Towne Orange, Fresno's Tower District and downtown Bakersfield. Copper can last a long time, but hard water and high pressure can cause pinhole leaks. Newer areas, like master-planned Irvine or newer tracts in Clovis, have younger pipes. A younger home is still not a leak-proof one.
If you are on the fence, a plumber can look at your leak history, pipe type and pressure together. Learn how whole-house repiping in PEX or copper works.
Signs to Act On Early
Here is the short list. Any one of these is worth a phone call, even if it seems small.
- Warm floor. You feel a hot spot on tile or wood.
- Running water sound. You hear it when nothing is on.
- Moving meter. It turns with everything shut off.
- Bill jump. Your water bill rises for no clear reason.
- Damp spots. You find wet carpet, swollen baseboards or a musty smell.
- New cracks. Tile cracks near where pipes run.
- Busy water heater. It seems to run all the time.
Catching a leak early often means a smaller repair and less water damage. In many cases, a slab leak can be fixed by rerouting the line with PEX instead of breaking up the floor. We find the cause first and explain your options. See how slab leak repair works.
A Seasonal Checklist for Central Valley and Orange County Homes
Orange County weather is mild. The valley has very hot summers and a few freeze nights each winter. In both regions, pipe care is mostly about pressure, scale and wear. Use this list to spread the work across the year.
Spring
- Test your water pressure with a hose bib gauge.
- Check sprinkler valves and lines before summer watering starts.
- Look under sinks for damp spots or crusty shutoff valves.
Summer
- Compare your water bill to last summer's bill.
- Check hose bibs for drips and cracked handles.
- Put the recirculation pump on a timer if you travel.
- Check garage and attic water heaters for leaks during heat waves.
Fall
- Flush sediment from your tank water heater.
- Check that the water heater straps are tight.
- Turn your main shutoff off and on to keep it moving.
Winter
- Do the meter test with everything turned off.
- Cover exposed outdoor pipes if a freeze night is forecast.
- Descale a tankless heater if its manual says to.
What Prevention Costs and What Drives the Price
Most prevention jobs are small. Still, prices vary from home to home, so we don't list numbers here. Call and describe what you have, and we'll give you a free quote over the phone. These are the things that move the price most.
- Regulator location. A valve that is easy to reach takes less time than a buried one.
- Pipe size and material. Larger or older lines may need more fittings.
- Expansion tank. It adds parts and labor when pressure spikes.
- Softener loop. Homes without a loop need new piping first.
- Pump controls. A timer is simpler to add than a button or sensor.
- Repipe size. More bathrooms, floors and fixtures mean more pipe and time.
- Access. Tight attics and finished walls add work.
Military and law enforcement households get 10% off their plumbing work.
When to Call a Professional
A lot of this list is safe to do yourself. Testing pressure, reading the meter, setting the heater and cleaning faucet screens are all fair game. Some jobs are not. A mistake on them can cause the very leak you want to prevent.
Leave These to a Licensed Plumber
- Pressure regulators. Replacing one means cutting into the main line.
- Expansion tanks. They have to be sized and supported right.
- Gas work. Leave gas water heaters and gas lines to a pro.
- A mystery leak. The meter moves, but you can't find the source.
- A bad main shutoff. It's stuck, leaking or broken.
- Water heater swaps. Most cities require a permit for these.
If you're not sure, ask. It costs nothing to describe the problem on the phone. We'll tell you if you can handle it or if it needs a licensed plumber.
Need a Plumber in the Central Valley or Orange County? Orange Independent Plumbing Is Ready to Help
Orange Independent Plumbing Services is a family-owned, licensed and bonded company that has served homeowners since 2015. Our California license is C-36 #1005919. We'll tell you plainly what needs work now.
We serve the Central Valley, from Bakersfield to Fresno, including Fresno, Bakersfield and Visalia. In Orange County, we serve Orange, Irvine, Tustin and Yorba Linda, plus Corona.
- Central Valley. Call (559) 706-2285.
- Orange County. Call (714) 904-6988.
Or contact us today to schedule service.